How Run Security Camera Cables Through Roof Into Ceiling Youtube

CCTV Installation and Wiring Options

Today there are a lot of options when it comes to choosing a quality CCTV security organization. You may decide to go with a traditional analog arrangement, Hard disk drive-SDI, HD-CVI or even an IP network based security products.

I affair all of these options accept in common is you will probably have to run some sort wire to the cameras. Yes, there are some "Wireless Security Camera" solutions bachelor on the market today, but if you exercise some research you volition observe that there are a lot of limitations to wireless security cameras. Near CCTV professionals would probably not recommend a wireless system in an environment where up-fourth dimension and security are disquisitional.

I do want to mention that it is possible to reliably transmit video wirelessly using a device such as the TP-LocoM5 – Wireless Access Point/Bridge every bit seen here at world wide web.securitycameraking.com.

But even and so you would even so need to have a power wire run to the camera or a local power source nigh the camera and information technology but works with IP Cameras.

That existence said, nosotros will be talking about a fully-wired organization in conjunction with a storage device such equally a DVR (Digital Video Recorder) or NVR (Network Video Recorder).

NEW INSTALLATION
When installing a completely new security system you may want to take the video and power wires come from a single location located near the storage device (DVR or NVR) as shown beneath.

ANALOG SYSTEMS
Analog, Hard disk drive-SDI and Hd-CVI cameras will need 2 wires run to them. I for video manual and a fix of power wires in order to ability the photographic camera. You lot could run a coax wire and separate ability wires only almost CCTV professionals choose to use "Siamese Cable". Siamese Cable is a manufactured coax cable with a set of power wires attached to it. The power wires can be separate off from the coax in cases where your power source may not be in a close proximity to your recording device.

NETWORK IP SYSTEMS
IP cameras employ digital video transmission over CAT5 or CAT6 cablevision. In most cases you run your video and power to and from the camera on the same CAT5 or CAT6 wire, assuming you are using a POE (Power Over Ethernet) ability source such as a POE injector or POE Switch.

Some NVRs come with built in POE,  just in most cases it is recommended to use an external POE switch similar the POE-8MB1G from SecurityCameraKing.com. When using an external POE switch all of your CAT5 or CAT6 will run directly from each camera to a POE switch that is continued to your local network. So you lot only connect your NVR to the network and yous are all gear up.

Most IP cameras also come up with an boosted power wire if you choose not to utilize POE and ability them with 12v or 24v power as shown beneath.

If you lot are going to power your IP camera with 12v /24v power  you lot will still run all of your CAT5 or CAT6 from the camera to a Non-POE switch (usually significantly less expensive than a POE switch) but y'all will run an actress set of power wires from a power source to each camera.

RUNNING YOUR CABLES

At present it's time to run your cable. The following will cover two pop scenarios.

Scenario one: Running your cable through your cranium and mounting your cameras to the soffit. This is a mutual installation option, provided you lot take access to your attic and your soffits are also accessible.

Starting time y'all accept to cull the placement of you recorder and power supply. Some people merely have them located in an office or a room within their habitation.  Others prefer having them in a more than secure location such as in a lockbox, hidden in a closet, or fifty-fifty in the cranium itself.

The image below shows the recorder and ability supply inside a room of the home. Power and video wires run upwards the wall into the attic to the location where the camera volition be located and out a small-scale hole in the soffit were the camera will be mounted.

Scenario 2: Another pick is to run your cable through an exterior wall and so utilize conduit on the outside of your construction to run your cables from i photographic camera to another. This is a bang-up option for those who do not have an cranium or limited admission to ane.

Mounting Your Cameras

Once you have run your wires to the desired location you can connect your camera. In some cases where the cables are coming out of the soffit information technology is possible to connect your wires together and tuck the connections up into the hollow expanse of the soffit, then mount the photographic camera straight to the soffit.

In situations where you're running your wires through a solid concrete or brick wall that the connections cannot be tucked into, it is common to mount a junction box.

Junction Boxes and Conduit
Junction boxes are particularly useful when running your cable through conduit on the exterior of your structure equally they serve equally a atmospheric condition proof container protect your power and video connections from the elements and likewise provide yous with a flat surface to mount your cameras to.

Offset you volition pull your wires through the access hole on the back of the junction box. And then mount the junction box to the wall. You may have to drill a hole in the junction box cover big enough to feed your camera connections through. Next, connect the camera to the power and video connection(s). Then spiral the cover on to the junction box. Now you lot can mount you camera to the junction box. See the diagram below.

When used on a soffit, a junction box will sometimes be helpful in gild to lower and driblet your cameras beneath obstructions such as deep fascia boards equally shown below.

Source: https://www.securitycameraking.com/securityinfo/cctv-installation-and-wiring-options/

Posted by: currylithapablout.blogspot.com

Share this post